How to Draw a Free Body Diagram Before Writing an Equation

Learning how to draw a free body diagram gives you a way to check a forces equation before you write it. Picture a crate sliding down a ramp. Gravity pulls straight down, but the crate accelerates along the ramp if the surface is frictionless. A good diagram keeps those directions separate. It also prevents a less obvious mistake: counting gravity once as a downward force and then again through its components.
How to draw a free body diagram in three steps
- Choose the object. Write its name above the sketch. Represent it with a dot or a simple box. The diagram shows the forces on that object, not all the forces in the scene.
- List the forces acting on it. Check what touches the object, then check for forces that act without contact, such as gravity. Draw and label one arrow for each force. For every arrow, name what exerts it.
- Choose and label your axes. Mark both positive directions before resolving any force. Choose axes that make the force equations easy to read, often by lining up an axis with a surface or with a known direction of acceleration.
Keep the scene sketch and the force diagram separate. The scene sketch can show the ramp angle and an arrow for the crate's velocity. The force diagram needs neither a velocity arrow nor an acceleration arrow among its forces. If you mark either quantity beside the diagram, label it clearly so you do not include it in a force sum. The OpenStax guide to drawing free body diagrams shows how this separation works when a problem has more than one object.
Isolate the crate and name the forces
Consider a crate of mass m sliding down a straight, fixed ramp. The ramp makes an angle θ with the horizontal. Take the surface to be frictionless, neglect air resistance, and assume the crate stays in contact with the ramp. In the scene sketch, draw the ramp. In the free body diagram, draw only the crate as a box or dot.
- Weight, mg: Earth pulls on the crate vertically downward. Here g is the magnitude of the local gravitational acceleration.
- Normal force, N: The ramp pushes on the crate perpendicular to its surface, away from the ramp. The word normal means perpendicular here.
That is the entire force list for this setup. The crate also pushes on the ramp, but that force belongs on a diagram of the ramp. It does not cancel the normal force in the crate's equation, because the two forces act on different objects. And the fact that the crate is sliding does not add a force in the direction of motion. If the ramp were rough and the crate were sliding downhill, kinetic friction from the ramp would be a real third force pointing uphill.
Choose axes that fit the ramp
Let positive x point downhill along the ramp and positive y point perpendicular to it, away from the surface. These axes tilt with the ramp. Now the normal force has only a y component, and the acceleration has only an x component. The crate stays against the straight ramp, so ay = 0.
Weight still points straight down. The angle between the weight arrow and the negative y direction is θ: the ramp is tilted by θ from horizontal, so its inward perpendicular is tilted by θ from vertical downward. In your component triangle, the leg next to θ has magnitude mg cos θ and points into the ramp. The opposite leg has magnitude mg sin θ and points downhill. Give each component its sign from the axes, not from the triangle:
- Wx = +mg sin θ
- Wy = −mg cos θ
If you forget which expression gets the sine, picture the ramp becoming horizontal. The downhill component should shrink to zero, and the inward component should become the full weight. At θ = 0, sine gives zero and cosine gives one, so the expressions pass that check.
Use the components without adding another force
The weight arrow and its two components describe the same pull from Earth. The components tell you how much of that pull belongs in each axis equation. Keep the original weight arrow on your force diagram and sketch the component triangle beside it, or make a separate component sketch where the two component arrows replace the weight arrow. If you draw all three arrows in one place, use dashed component arrows and label them as parts of the weight.
With the axes chosen above, Newton's second law gives:
- Along the ramp: ΣFx = mg sin θ = max.
- Perpendicular to the ramp: ΣFy = N − mg cos θ = 0.
There is no extra mg term in either equation. The downhill equation already includes gravity's contribution along the ramp, and the perpendicular equation already includes its contribution into the ramp. Adding a full weight term would both double count gravity and put a vector that points straight down into a sum that needs signed components along just one axis. The equations give ax = g sin θ and N = mg cos θ.
Practice changing one detail at a time
Redraw the crate with the same axes but give it an initial velocity uphill on the frictionless ramp. The force diagram does not change. The velocity points uphill while the acceleration points downhill, so the crate slows as it moves uphill. Now make the surface rough while the crate is still sliding uphill. Add a kinetic friction arrow downhill: it opposes the crate's sliding relative to the ramp, not the downhill component of gravity.
When you work through the IPhyC training and practice problems, try stopping after the force diagram to name the source of every arrow. For more study techniques, see the exam preparation articles.
Frequently asked questions
Do I draw acceleration on a free body diagram?
Acceleration is not a force, so do not include it among the force arrows. You can label it separately beside the diagram.
Do my axes have to line up with the ramp?
No. Horizontal and vertical axes also work, but ramp-aligned axes put the normal force and acceleration each along a single axis in this example.
Should I draw weight and both of its components?
You can show all three for reference if you clearly mark the components as parts of the weight. When you write the axis equations, use only the signed component of weight along each axis.


